Installing a Brick Paver Walkway or Ash Bricks

The use of Setting up a Brick Paver Walkway or Loose Bricks or Pavers to produce a walkway or patio complements a house in a method that is unrivaled. It adds a level of quality and beauty to a home entrance that can not be accomplished with either concrete or asphalt. Brick and Pavers also can be found in various colors and shapes allowing for distinct color design and patterns to be attained. In addition, installing a Brick or Paver sidewalk does not always require a pro. With some standard understanding and a relatively easy pathway strategy, a homeowner is capable of carrying out such a job.

The secret to setting up a Brick or Paver Walkway is to very first effectively prepare the area where the bricks/pavers are to be installed. The location must be dug out a minimum of a foot down, getting rid of all topsoil and clay soil. In addition, string lines ought to be strung on each side of the walkway. The string lines indicate the ended up height of the pathway.
Once the area has been dug down, 3/4" gravel stone need to be laid in and tamped down securely. 2" of sand, or stone dust ought to be spread out over the gravel. Once again the sand/stone dust should be tamped down. Stone dust is preferred. The height between the tamped down sand and the stringline ought to equal the density of the brick or paver.

Now that you have a steady base, position a 1" pipe or journal board the length of the pathway on either side of the sidewalk. Using a flatedge, e.g. a 2"x4" board, slide it over the two lengths of the pipe/ledger board. In doing this you will produce a level surface area to lay the bricks/pavers.

Now put on the level sand/stone dust strips of plastic brick borders. Install a run on both sides of the ready area. These strips will act as your pathway border and help to maintain the integrity and shape of the sidewalk. You can get these plastic strip borders at a lot of house improvement stores. The strips ought to be anchored down with 12" galvinized nails. You ought to sink these nails into the ground and through the strips every foot.

You can then start to lay the bricks/pavers when this bricks stones is done. There are many patterns you can lay. I especially like the Herring Bone pattern. The key to laying the bricks/pavers is to guarantee that they interlock with each other. Always stagger surrounding rows of bricks by 1/2 of a brick to interlock them. This will once again help maintain the stability of the sidewalk.

Undoubtedly bricks/pavers will need to be cut or divided when constructing the sidewalk. Unless you wish to purchase or rent a costly wetsaw, I would recommend acquiring a simple brick/paver splitter. It is basically a sculpt with a wide end that is the width of the bricks/pavers. To really cut/split the brick/paver, lay it in a bed of sand and place the sculpt at a 75 degree angle over the spot where you want to break the brick. Using a hammer strike the butt end of the sculpt strongly. You might require to do this a couple of times. You might also desire to turn the brick/paver over and strike the other side of the brick utilizing the hammer and chisle. Within one or two strikes the brick/paver ought to break cleanly. If your walkway has curves you will require to buy/rent a wetsaw.

After setting up the bricks, develop the outdoors edges with additional sand, and then shovel in the topsoil and pack down firmly.
Spread stone dust over the brand-new pathway and sweep into the fractures. This will complete the interlocking of the bricks and assist to remove any weed development.


In addition, installing check here a Brick or Paver pathway does not necessarily need a pro. The secret to setting up a Brick or Paver Walkway is to very first correctly prepare the area where the bricks/pavers are to be set up. Now that you have a steady base, position a 1" pipe or ledger board the length of the walkway on either side of the sidewalk. These strips will act as your pathway border and assistance to maintain the stability and shape of the sidewalk. Undoubtedly bricks/pavers will require to be cut or split when developing the sidewalk.

Leave a Reply

Your email address will not be published. Required fields are marked *